Ошибка F1

Народ! Может кто подскажет, что означает мигание F1 два длинных три коротких. Замигала после Керхера. Заводится и едет как и раньше. Заранее благодарю за ответы.

23 Blinks - Engine operates normally
Open or short circuit in right O2 sensor heater wire:
Faulty right O2 sensor

Решил сбросить все ошибки. Сам,оторвав разъем,при замене воздушного фильтра,искал-помогло. Пусть будет:
list FI Codes:
MIL = Malfunction Indicator Lamp also referred to as FI

If FI (Fault Indicator) light comes on pull over but DO NOT shut bike off.
Put in neutral and put side stand down, RPMs below 1500. This signals the ECM to send the error code to the FI light. Count the number of long and short flashes. This will give you the error code.

If you shut the bike off the error code is lost - sort of. It will be retained in the ECM but it is harder to get out. If the bike stops and the will not restart you can get the FI light to flash the error code by cranking the engine for 10 seconds. The FI light will then flash the error code.

Long Blink = 10
Short Blink = 1
i.e. long long long short short short = 33 check error code 33

Number of MIL blinks . Symptoms .Cause

0 No blinks - Engine does not start
Open circuit in the power input and ground wires of the ECM: Faulty bank angle sensor
Open circuit in bank angle sensor related wires: Faulty FI IGN relay: Open circuit in FI IGN relay related wires
Faulty engine stop switch: Open circuit in engine stop switch related wires: Faulty ECM: Blown FI IGN fuse (20 A)
Blown ST. KILL fuse (10 A):

0 No blinks - Engine operates normally
Open circuit in MIL wire: Faulty combination meter: Faulty ECM

0 Stays lit - Engine operates normally
Short circuit in service check connector wire: Short circuit in MIL wire: Faulty ECM

1 Blinks - Engine operates normally
Loose or poorly connected MAP sensor connector:
Open or short circuit in MAP sensor wire:
Faulty MAP sensor

7 Blinks - Hard to start at a low temperature (ECM controls using preset value; coolant temperature: 85° C/185° F)
Loose or poorly connected ECT sensor connector:
Open or short circuit in ECT sensor wire:
Faulty ECT sensor

8 Blinks - Poor engine response when operating the throttle quickly (ECM controls using preset value; throttle opening: 0° )
Loose or poorly connected TP sensor connector:
Open or short circuit in TP sensor wire:
Faulty TP sensor

9 Blinks - Engine operates normally (ECM controls using preset value; intake air temperature: 28° C/82° F)
Loose or poorly connected IAT sensor connector
Open or short circuit in TP sensor wire:
Faulty IAT sensor

10 Blinks - Engine operates normally at low altitude
Engine idles roughly at a high altitude (ECM controls using preset value; barometric pressure: 760 mm Hg/1,013 hPa)
Loose or poorly connected BARO sensor connector:
Open or short circuit in BARO sensor wire:
Faulty BARO sensor

11 Blinks - Engine operates normally
Loose or poorly connected vehicle speed sensor connector
Open or short circuit in vehicle speed sensor wire:
Faulty vehicle speed sensor

12 Blinks - Engine does not start
Loose or poorly connected No. 1 injector connector:
Open or short circuit in No. 1 injector wire:
Faulty No. 1 injector

13 Blinks - Engine does not start
Loose or poorly connected No. 2 injector connector:
Open or short circuit in No. 2 injector wire:
Faulty No. 2 injector

14 No blinks - Engine does not start
Loose or poorly connected No. 3 injector connector:
Open or short circuit in No. 3 injector wire:
Faulty No. 3 injector


15 Blinks - Engine does not start
Loose or poorly connected No. 4 injector connector:
Open or short circuit in No. 4 injector wire:
Faulty No. 4 injector

16 Blinks - Engine does not start
Loose or poorly connected No. 5 injector connector:
Open or short circuit in No. 5 injector wire:
Faulty No. 5 injector

17 Blinks - Engine does not start
Loose or poorly connected No. 6 injector connector:
Open or short circuit in No. 6 injector wire:
Faulty No. 6 injector

18 Blinks - Engine does not start
Loose or poorly connected camshaft position sensor connector
Open or short circuit in camshaft position sensor wire:
Faulty camshaft position sensor

19 Blinks - Engine does not start
Loose or poorly connected ignition pulse generator connector:
Open or short circuit in ignition pulse generator wire:
Faulty ignition pulse generator

21 Blinks - Engine operates normally
Open or short circuit in right O2 sensor wire:
Faulty right O2 sensor

22 Blinks - Engine operates normally
Open or short circuit in left O2 sensor wire:
Faulty left O2 sensor

23 Blinks - Engine operates normally
Open or short circuit in right O2 sensor heater wire:
Faulty right O2 sensor

24 Blinks - Engine operates normally
Open or short circuit in left O2 sensor heater wire:
Faulty left O2 sensor

25 Blinks - Engine operates normally
Loose or poorly connected right knock sensor connector:
Open or short circuit in right knock sensor wire:
Faulty right knock sensor

26 Blinks - Engine operates normally
Loose or poorly connected left knock sensor connector:
Open or short circuit in left knock sensor wire:
Faulty left knock sensor

29 Blinks - Engine stalls, hard to start, rough idling
Loose or poorly connected idle air control (IAC) valve connector:
Open or short circuit in IAC valve wire:
Faulty idle air control valve

33 Blinks - ECM does not hold the self diagnostic data
Faulty E2-PROM in ECM Engine operates normally

41 No blinks - Engine operates normally
Loose or poorly connected connector in gear position switch related circuits
Open or short circuit in gear position switch wires:
Faulty gear position switch:
Faulty clutch switch:
Faulty side stand switch

В общем по нашему - накрылся правый лямбда-зонд. Спасибо тебе добрый человек!

У меня было все ошибки, по датчику ХХ и одном (не помню, какому точно) лямбда-зонду. Проблема оказалась не в датчиках, а +15 пропал с них. Вскрыл проводку, кинул дополнительный +15 и все заработало ...

после мойки посоветовал бы проинспектировать проводку,коль так случилось и горит F1. Скорее всего окисления.